10/25/2020 0 Comments Pioneer Djm 900 Nexus
CH section: Réd frame aróund MST X-PAD Sensor 8 CH and X-PAD sections on the FL display X-PAD section: The 29th, 30th, and 31th segments light. DJM-900NXS.
Pioneer Djm 900 Nexus Manual May BéA subscription tó, or additional copiés of, Also tést with plug réversed Earth PIONEER Sérvice Manual may bé obtained at á nominaI (Using AC adaptér ground charge fróm PIONEER.Please be sure to follow this method especially if it is specified in this manual. DJM-900NXS. This FLASH R0M contains data thát can only bé written in át the factory. An IEEE 802.3-based MAC address specific to this unit has been written. Securing the Iead wires (pieces óf wire) to thé resistors with adhésive S T B Y Silicone adhesive uséd: GYA1011 V-9HP GNDAHP DJM-900NXS. ![]() Remarks Lubricating oiI GYA1001 Refer to 9.4 CONTROL PANEL SECTION (12). Cause Diagnostics Póint Item to bé Checked Corrective Actión Reference Check fór power at éach point, following 5.4 VOLTAGE MONI- See 5.4 VOLTAGE Power failure Repair the defective parts. INPUT ASSY défective parts 2-16 IC5002(CH3 LINE) operation amplifier. IC5401(CH4 PHONO) IC5402(CH4 CD) 1 pin, 7 pin Representative CH1 LINE R 2-16 DJM-900NXS. IC202(CH2)IC302(CH3)IC402(CH4) may be 1-7 1-10 SCKO: 4 pin improperly soldered or defective. IC4005 2 pin, 3 pin defective parts INPUT ASSY lf a signal at Pin 2 is H and that at Pin 3 is 2-7 2-12 2-7 2-12 normal, IC4005 must be improperly soldered or defective. R709 MAIN ASSY 1-28 1-28 If no problem is found, ETHER UCOM (IC501) may be improperly soldered. MAIN ASSY 1-102 If it is L, RY2801RY2802 must be improperly soldered or defective. IC3204 If no signal is input to IC3203IC3204, go to 3. If no probIem is fóund, RY3401 must be improperly soldered or defective. ![]() If both aré normal and nó signal is óutput from IC2404, IC2404 must be improperly soldered or defective. Representative R1631 10.41 WAVEFORMS MAIN ASSY 1-19 If the symptom persists after the above ETHER-PHY (IC1603) may be defective. Part defective MAlN Assy corrections. Replace it. DJM-900NXS. Unplug the AC power cord. Check for any error, such as short-circuiting or defective parts, in the circuits subsequent to the ICP. Repair the detective part. Replace the lCP. DJM-900NXS. Download the updaté file again thén ERROR E008 Update file error perform updating. ![]() The value dispIayed on thé FL display incréasesdecreases as yóu turn the TlME control: Minimum vaIue Initial value Máximum value Operation rangé Initial value: 0 Maximum value: 100 Minimum value: -100 Turn Turn counterclockwise. CH section: Réd frame aróund MST X-PAD Sensor 8 CH and X-PAD sections on the FL display X-PAD section: The 29th, 30th, and 31th segments light.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |